华为S7706核心交换机配置信息？

2025-04-27 19:54:10

推荐回答（1个）

回答1：

S7706集群的配置：1.配置集群系统与上、下游设备的Eth-Trunk
system-view[S7706A01] sysname ZAHD-S7706-01
//给集群系统重新命名[ZAHD-S7706-01] interface eth-trunk
10[ZAHD-S7706-01-Eth-Trunk10] quit[ZAHD-S7706-01] interface
xgigabitethernet 1/1/0/3[ZAHD-S7706-01-XGigabitEthernet1/1/0/3]
eth-trunk 10[ZAHD-S7706-01-XGigabitEthernet1/1/0/3] quit[ZAHD-S7706-01]
interface xgigabitethernet
2/1/0/4[ZAHD-S7706-01-XGigabitEthernet2/1/0/4] eth-trunk
10[ZAHD-S7706-01-XGigabitEthernet2/1/0/4] quit

[ZAHD-S7706-01]
interface eth-trunk 20[ZAHD-S7706-01-Eth-Trunk20] quit[ZAHD-S7706-01]
interface xgigabitethernet
1/1/0/4[ZAHD-S7706-01-XGigabitEthernet1/1/0/4] eth-trunk
10[ZAHD-S7706-01-XGigabitEthernet1/1/0/4] quit[ZAHD-S7706-01] interface
xgigabitethernet 2/1/0/3[ZAHD-S7706-01-XGigabitEthernet2/1/0/3]
eth-trunk 20[ZAHD-S7706-01-XGigabitEthernet2/1/0/3]
quit两套集群系统互为代理在每个集群系统上执行命令system-view，进入系统视图。执行命令mad domain
domain-id，配置集群系统MAD域值。缺省情况下，集群系统MAD域值为0。说明：设备支持两套集群系统互为代理进行多主检测，此时必须通过配置保证两套集群系统的MAD域值不同。执行命令interface
eth-trunk trunk-id，进入Eth-Trunk接口视图。执行命令mad
relay，在Eth-Trunk接口上启用代理功能。执行命令mad detect mode
relay，配置Eth-Trunk接口的代理方式多主检测功能。
S7706A01的配置：1.配置集群连接方式、集群ID及集群优先级HUAWEI>
system-view[HUAWEI] sysname S7706A01[S7706A01] set css mode
lpu[S7706A01] set css id 1[S7706A01] set css priority
1002.配置逻辑集群端口[SwitchA] interface css-port 1[SwitchA-css-port1] port
interface xgigabitethernet 1/0/1 to xgigabitethernet 1/0/2
enable[SwitchA-css-port1] quit3.使能集群功能[SwitchA] css enableWarning: The
CSS configuration will take effect only after the system is rebooted.
The next CSS mode is LPU. Reboot now? [Y/N]:y
S7706A02配置：1.配置集群连接方式、集群ID及集群优先级HUAWEI>
system-view[HUAWEI] sysname S7706A02[S7706A02] set css mode
lpu[S7706A02] set css id 2[S7706A02] set css priority
102.配置逻辑集群端口[SwitchB] interface css-port 1[SwitchB-css-port1] port
interface xgigabitethernet 1/0/1 to xgigabitethernet 1/0/2
enable[SwitchB-css-port1] quit3.使能集群功能[SwitchA] css enableWarning: The
CSS configuration will take effect only after the system is rebooted.
The next CSS mode is LPU. Reboot now? [Y/N]:y
S5700集群的配置：1.配置集群系统与上、下游设备的Eth-Trunk
system-view[S7706A01] sysname ZAHD-S7706-01
//给集群系统重新命名[ZAHD-S7706-01] interface eth-trunk
10[ZAHD-S7706-01-Eth-Trunk10] quit[ZAHD-S7706-01] interface
xgigabitethernet 1/1/0/3[ZAHD-S7706-01-XGigabitEthernet1/1/0/3]
eth-trunk 10[ZAHD-S7706-01-XGigabitEthernet1/1/0/3] quit[ZAHD-S7706-01]
interface xgigabitethernet
2/1/0/4[ZAHD-S7706-01-XGigabitEthernet2/1/0/4] eth-trunk
10[ZAHD-S7706-01-XGigabitEthernet2/1/0/4] quit

[ZAHD-S7706-01]
interface eth-trunk 20[ZAHD-S7706-01-Eth-Trunk20] quit[ZAHD-S7706-01]
interface xgigabitethernet
1/1/0/4[ZAHD-S7706-01-XGigabitEthernet1/1/0/4] eth-trunk
10[ZAHD-S7706-01-XGigabitEthernet1/1/0/4] quit[ZAHD-S7706-01] interface
xgigabitethernet 2/1/0/3[ZAHD-S7706-01-XGigabitEthernet2/1/0/3]
eth-trunk 20[ZAHD-S7706-01-XGigabitEthernet2/1/0/3] quit

两套集群系统互为代理在每个集群系统上执行命令system-view，进入系统视图。执行命令mad
domain
domain-id，配置集群系统MAD域值。缺省情况下，集群系统MAD域值为0。说明：设备支持两套集群系统互为代理进行多主检测，此时必须通过配置保证两套集群系统的MAD域值不同。执行命令interface
eth-trunk trunk-id，进入Eth-Trunk接口视图。执行命令mad
relay，在Eth-Trunk接口上启用代理功能。执行命令mad detect mode
relay，配置Eth-Trunk接口的代理方式多主检测功能。
S5700A01的配置：1.配置集群连接方式、集群ID及集群优先级HUAWEI>
system-view[HUAWEI] sysname S5700A01[S5700A01] set css mode
lpu[S5700A01] set css id 1[S5700A01] set css priority
1002.配置逻辑集群端口[S5700A01] interface css-port 1[S5700A01-css-port1] port
interface gigabitethernet 1/0/51 to xgigabitethernet 1/0/52
enable[S5700A01-css-port1] quit3.使能集群功能[S5700A01] css enableWarning: The
CSS configuration will take effect only after the system is rebooted.
The next CSS mode is LPU. Reboot now? [Y/N]:y
S5700A02的配置：1.配置集群连接方式、集群ID及集群优先级HUAWEI>
system-view[HUAWEI] sysname S5700A02[S5700A02] set css mode
lpu[S5700A02] set css id 2[S5700A02] set css priority
102.配置逻辑集群端口[S5700A02] interface css-port 1[S5700A02-css-port1] port
interface gigabitethernet 1/0/51 to xgigabitethernet 1/0/52
enable[S5700A02-css-port1] quit3.使能集群功能[S5700A02] css enableWarning: The
CSS configuration will take effect only after the system is rebooted.
The next CSS mode is LPU. Reboot now? [Y/N]:y

END

注意事项

其中7706 5700都是基于业务口的集群。
三层交换机都是可以设置路由端口的,s3300系列以上的都支持端口路由配置,端口IP化,77系列比33系列还要高,因此是可以支持的。